FURE SHING TORQUE LIMITER
|
TORQUE LIMITER TL250、TL350、TL500、TL700 |
||||||||||||||||||||||||||||
|
１.Assembly
Component parts of a torque limiter is illustrated as
follower so mount each part on a torque limiter hub in order, as a center
member a sprocket, a gear or a pulley can be assembler in before
assembly, each part shall be clean and free form oil , grease , dust and
rust.
|
||||||||||||||||||||||||||||
|
|
2.Bushing 3. Friction plate 4. pressing plate 5. Disk spring 6. Adjusting nut 7. Set screw 8. Lock washer
|
|
2.Bushing 3. Friction plate 4. pressing plate 5. Disk spring 6. Pilot Plate 7. Adjusting nut 8. Adjusting Bull 9. Set Screw |
|||||||||||||||||||||||||
|
２.The
central part processing accuracy
A central part rubbing surface (side) please completes by the 3S ~ 6S degree. Also the central part hole (and axle bushing union are partial) also please completes by 3S ~ 6S. |
||||||||||||||||||||||||||||
|
３.Is
suitable the revolution
Is suitable the revolution (to be suitable rubbing surface) good also to be allowed to use, but when wants to slide the accuracy must be better, please do illuminate the next table the Watt torque by 150rpm below, lets his idle operation almost 500 rotations.
|
||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||
|
４.Torque hypothesis
The torque hypothesis is installs in the machinery which actual uses, but slowly tightens by the commonly used torque the adjusting nut or the screw to does not slide up to, established add-on has surpassed the torque to confirm whether could slide the method for most suited. Also the next table related locking - torque graph may understand each adjusting nut or the screw locking to the torque summary, therefore please do for the locking reference.
|
||||||||||||||||||||||||||||
|
５.Adjusting nut and adjusting screw locking way
TL250, 350 adjusting nut is the hexagonal nut, therefore by the screw locking to the suitable position, is please fixed by the hexagonal nut. TL500, the TL700 adjusting nut is the circular nut and attaches 3 adjusting screws (to press with screw). Is going against the spring by the leader metal plate, but locks the adjusting nut importantly pastes (adjusting screw to the leader metal plate surface and the adjusting nut surface is loose condition) cannot have the gap up to, again each adjusting screw average locking to appropriate position.
|
||||||||||||||||||||||||||||
|
６.Maintains attention which and uses
Has adjusted hypothesis torque, in use because of rubbing surface change ambient temperature, humidity, other inevitable conditions but some times can change, therefore has the need periodic inspection to confirm the hypothesis the torque. The friction plate, the axle bushing is the components which uses in exchange has the stock, therefore like wore but cannot use time, please replace. Also has when the use like the oil, the water and so on bumps into the rubbing surface, sometimes the torque hypothesis can change, therefore must avoid the oil, the water as far as possible and so on.
|
||||||||||||||||||||||||||||
|
TORQUE LIMITER
Coupler TL250-C、TL350-C、TL500-C、TL700-C |
||||||||||||||||||||||||||||
|
In advance has established the torque killer, installs in the one side axis, but the one side axis, installs the B in addition lock wheel, then to the chain link tucks can take the coupler use the form, is the torque definition coupler.
|
||||||||||||||||||||||||||||
|
●Installs the way
The axis prominent accuracy is two locks turn of teeth bottom, the laying aside ruler (above 3) confirmed two locks a turn of gap (next table S size) and the parallelism. After completes prominently, two locks turn to the chain link tucks fixes in the insertion joint needle.
|
||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||
|
|
|
|||||||||||||||||||||||||||
